The exact command tree varies by product generation (MINI-LINK TN, MINI-LINK PTX, or MINI-LINK 6000 series), but the following covers common available in the CLI. 1. Basic System & Access Features | Feature | Example CLI Command | Description | |---------|--------------------|-------------| | Login / Logout | login , logout | Authenticate to CLI session | | Privilege levels | enable , disable | Enter/exit executive mode | | Session management | exit , quit | Terminate current session level | | System info | show system info | HW/SW version, uptime, serial number | | Date/time | show clock , clock set | View or set system time | 2. Configuration Management | Feature | CLI Command | |---------|--------------| | Enter config mode | configure terminal | | Save config | write memory or copy running-config startup-config | | Show running config | show running-config | | Show startup config | show startup-config | | Reset to defaults | config default (with caution) | | Backup config (TFTP/FTP) | copy running-config tftp://<ip>/file.cfg | 3. Radio Link & Interface Features | Feature | CLI Command | |---------|--------------| | Radio parameters | show radio 0/1 – freq, tx power, modulation | | Set frequency | radio frequency <MHz> | | Tx power | radio tx-power <dBm> | | ATPC enable/disable | radio atpc on/off | | Adaptive modulation | radio adaptive-modulation enable/disable | | Link status | show link 0/1 – lock, RSSI, BER | | Ethernet interface config | interface ethernet 0/1 → ip address ... | 4. Ethernet / L2 Switching Features | Feature | CLI Command | |---------|--------------| | VLAN configuration | vlan database , vlan <id> | | Port mode (trunk/access) | switchport mode trunk/access | | QoS / CoS | class-map , policy-map , set cos | | Ethernet OAM | ethernet oam enable/disable | | Link aggregation (LAG) | channel-group <id> | | Port statistics | show interface ethernet 0/1 counters | 5. IP & Routing Features | Feature | CLI Command | |---------|--------------| | Management IP | ip address <a.b.c.d/m> | | Default gateway | ip default-gateway <a.b.c.d> | | Static route | ip route <dest> <mask> <next-hop> | | Ping / Traceroute | ping <ip> , traceroute <ip> | | ARP table | show arp | | DNS config | ip name-server <ip> | 6. Synchronization (Sync/Ethernet) | Feature | CLI Command | |---------|--------------| | Sync source selection | sync source gps/line/radio | | SyncE enable | synchronous ethernet enable | | Clock quality (SSM/QL) | clock quality <value> | | Show sync status | show sync status | 7. Alarms & Performance Monitoring | Feature | CLI Command | |---------|--------------| | Active alarms | show alarms active | | Alarm history | show alarms history | | Performance monitoring (15/24h) | show performance radio/ethernet <interval> | | RSSI over time | show rssi history | | BER (Bit error rate) | show ber | | SNMP trap config | snmp-server host <ip> community <string> | | Syslog | logging <ip> , show logging | 8. Security & Access Control | Feature | CLI Command | |---------|--------------| | Change password | password | | User management | username <name> privilege <level> password | | SSH enable/disable | ip ssh enable/disable | | ACL (Access list) | access-list <num> permit/deny ... | | HTTP/HTTPS access | ip http server enable/disable , ip http secure-server | 9. Maintenance & Troubleshooting | Feature | CLI Command | |---------|--------------| | Loopback test (local/remote) | loopback local/remote radio/ethernet | | Software upgrade | upgrade software tftp://<ip>/<file> | | Reboot system | reboot | | Factory reset | factory-reset | | Diagnostic tools | debug radio/ethernet/ip (vendor-specific) | | Show hardware | show hardware inventory | | Temperature / voltage | show environment | 10. Wireless Link Optimization (Advanced) | Feature | CLI Command | |---------|--------------| | Link ID / Site name | system site-name <name> | | ATPPC (Advanced Tx Power Control) | radio atppc enable/disable | | XPI (Cross Polar Interference) | radio xpi on/off | | ACM threshold config | radio modulation-threshold <value> | ⚠️ Note: Actual commands differ between MINI-LINK TN (CLI similar to Cisco IOS), MINI-LINK PTX (more E/// specific), and MINI-LINK 6000 (often managed via WebUI/OSS-RC). Use ? and show ? in the CLI to explore available commands for your exact model. If you need a complete command reference for a specific MINI-LINK series (e.g., TN, PTX, 6600), please specify.